Stallion Technologies Software Release Note ===================== ATA Driver for SCO UNIX & Open Server 5 --------------------------------------- NOTE: The ATA driver for SCO Open Server 5 will install on Open Server 5 but will not install on SCO UNX 3.2.x. THe dual ATA driver for SCO UNIX & Open Server 5 will install on either. CONTENTS ======== 1. General 2. Release History _______________________________________________________________________________ 1. General =========== Media Format ------------ The ATA SCO UNIX & Open Server 5 driver is delivered in gzip format and is a full driver diskette. The gzip file is a raw diskette image and needs to be written to a 1.44Mb diskette. Disk Image Contents ------------------- The disk image contains the SCO UNIX & Open Server 5 driver for EasyConnection and EasyIO. Discontinued cards are also supported. _______________________________________________________________________________ 2. Release History =================== ATA 5.5.1 ========= Date 19 April 99 Ver 5.5.1 Prev 5.4.1 Characteristics --------------- Bus Architectures Supported: [Y] ISA [Y] MCA [Y] EISA [Y] PCI Description of Release: This is a general release of the ATA driver for SCO UNIX & Open Server 5. Compatible with: All previous versions. New features and changes: 1. Bug fixes as listed below. 2. Support for the EasyConnection Rapid Access (EC RA-PCI) card. Bugs Fixed ---------- 2141 D3 bug ALL - Signetics based products change LF to LF/CR instead of CR 2149 D3 bug SV3 - SCO driver does not wait for new POSIX XCSETA ioctls corr 2180 D3 bug ALL - Problem in driver informing RX Break event 2248 D3 bug SV3 - ATA 5.4.0 fails to receive notifies for all RXBREAK chars 2319 D3 ftr ALL - Switch to disable receiver during RS485 transmission 2435 D3 bug ALL - CD1400-RS422 panels do NOT support RI - SW has a bug 2490 D3 bug SV3 - bccstty -d fails except for devices named /dev/tty1aXX 2493 D2 bug SV3 - Attached printers hang on CDK based boards ATA 5.4.0 ========= Date 4 December 97 Ver 5.4.0 Prev 5.3.1 Characteristics --------------- Bus Architectures Supported: ISA : Yes MCA : Yes EISA : Yes PCI : Yes Description of Release: This is a general release of the ATA drivers for all supported operating systems. This is the first driver to support the new EasyIO-PCI and EasyConnection 8/64-PCI boards. It is also the first release to support the EasyConnection XP16 module. Compatible with: All previous ATA drivers. New features and changes: 1. Support for the EasyIO-PCI board. 2. Support for the EasyConnection 8/64-PCI board. 3. Support for the EasyConnection XP16, XP8D4, XP8R and XP16R Modules. 4. bugs fixed. Bugs Fixed ---------- 1158 D3 bug ALL - MCA config for EC8/32-MC is wrong 1402 D4 sug ALL - Increase easyadm's default cps for easyterm attached prin 1427 D3 bug ALL - RTS can get stuck low 1490 D3 ibg SV3 - the values of TIOCMGET and friends is incorrect 1512 D3 bug SV3 - IGNPAR and INPCK modes do not work 1516 D3 bug SV3 - ONboards cannot share memory under ATA5 1517 D3 bug SV3 - Stats beaks wait for drain 1519 D3 bug SV3 - Flushes can break wait for drain 1525 D1 bug SV3 - ATA 5.1.3 and ONboardE/16 ports boards panics 1535 D4 bug SV3 - The SCO installation will install on AT4 (without warning 1539 D3 bug ALL - ONboard/Brumby output performance reduced under ATA 5.1.3 1551 D1 bug ALL - Diags hangs with Level interrupts configured 1556 D4 sug ALL - Attached printer default cps speed 1577 D3 bug ALL - Cacheing doesn't work with old boards under ATA5 1579 D3 bug ALL - corto test crashes slave of ONboard32 1588 D3 bug SV3 - Port hangs if closed when flow controlled. 1597 D4 bug ALL - changing board types can confuse easyadm about resources 1600 D4 bug ALL - Allport stats screen help doesn't describe fields 1605 D3 bug ALL - mapcts flag does not work on ONboards and Brumbys 1607 D3 bug ALL - The ATA5.2 2681 slave crashed on most 128K brumbies 1614 D3 bug SV3 - Attached printer data prints on terminal, not printer 1641 D3 bug SV3 - Modem devices that have session or attatched printers hav 1644 D2 bug ALL - Onboards and Brumbies still don't work reliably with ATA5 1669 D3 bug SV3 - Sessions and Attached printers don't work 1670 D4 bug SV3 - Easyadm doesn't recognize the LOBLK flag 1730 D4 bug SV3 - Undefined flag in gettdefs errors from easyadm 1736 D3 bug SV3 - getty and uugetty -r flag no longer valid 1779 D3 bug SV3 - Onboard loses characters with ixany 1886 D3 bug SV3 - Easyadm creates bad major number for devices with major o 1890 D3 bug ALL - EIO-4 rev 3.0 HW change requires Easyadm update 1970 D2 bug SV3 - Creating APS/MSS on Brumby/ONboard modems fails on 2nd po 2006 D3 bug SV3 - Driver doesnt disable onboard when mapchan detected 2078 D3 bug SV3 - easyadm reports undefined ttydefs flags 2106 D3 bug SV3 - Scancode support broken 2108 D3 bug SV3 - Listing file greater 2048 bytes causes file to be output 2109 D3 bug SV3 - Port setup not preserved when ATA installed over itself 2140 D3 bug ALL - Input buffer flushing causes software flow control to bre _______________________________________________________________________________ [END]